• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Go About Boarding Up a Door

Boarding up a door is one method to shield vacant investment properties from the elements. Although it isn't able to be able to prevent all damage, it can reduce some of the problems caused by severe storms.

The commercial boarding up service up of windows and doors will also discourage trespassers and vandals. However it can be costly and time-consuming to install plywood boards over the openings of a property.

Measure the Door

You'll require a tape measure. It is also advisable to have a ladder or chair handy in case you need to get a better look at the top of the frame. Wear gloves and safety glasses if you have to make use of these tools.

Start by measuring the door's width. This can be done by running a tape measure horizontally along the door. Make sure to remove any other door components, such as the door sweep to get this measurement. Then, you can take the height measurement by measuring emergency boarding up 24/7 from the floor to the existing sill plate or lintel. It is crucial to take measurements in several locations, especially when measuring older doors as they may not have an exact rectangular shape. If the measurements differ take the largest number.

After you've logged the measurements of height and width, you'll need to figure out what size board you'll need for the frame. Ideally, it should be 2'' wider than the door and 1 2'' higher. This will allow you enough space to shim the door and frame in place.

When you're ready to measure the door frame's width and height measurements It's a good idea to remove any trim or casing the door jambs, so you can see the studs behind them. This will help you to determine the exact dimensions of the space between the studs and the frame.

After you have removed the trim, measure the length of your door frame using a tape measure. Measure the frame at three different places and use the smallest measurement. You should also determine the height of the frame from the top to bottom on both sides and use the shortest measurement as your door's height.

If you're having difficulty with the measurements, you should consult a professional to come to your home and take the measuring. They will tell you what size and style of door you'll need and how to prepare your frame for a new door.

Cut the Plywood

A door frame is typically made of a series of thin boards or studs that create a hollow space around the door. A typical door is held in place by two hinges connected to the studs. If you want to finish a door, you will have to take it off its hinges over night. To prevent insects from entering your home and to secure the door's opening, a straightforward method to board doors is to place plywood in the opening. It is simple to do without the need to nail or screw the plywood to the door frame.

Plywood is affordable, simple to work with and looks stunning when finished. This makes it the perfect material to provide temporary solutions to problems that require the removal of an existing door while finishing or installing a new one. It can also be useful to secure the opening of the room being renovated, like an unfinished basement or a construction site.

To install a plywood wall, start by taking measurements of the width and height of the door opening. Note the measurements using an utility knife and a straight edge made of metal like a drywall or a metal square. Then, draw an outline of chalk across each line to indicate where you want to cut. Then you can use circular saws to cut the plywood to the desired size.

When cutting the plywood it is essential to protect your eyes and ears. Wear earplugs or goggles that are protective whenever possible. It is also essential to use a sharp blade with many teeth, that will allow you to cut quickly and with little tear-out. To reduce the chances of tearing out pieces of wood from the edges of the cut, use a small block of wood as template to guide the blade and keep it just a hair's width away from the line while cutting.

A great way to hold the plywood in place without screwing it to the studs is to attach braces that are short at each end. Set one brace inside and the other outside of the door. Position a pair 1-1/2-inch deck screws in each hole, and then tighten with an open-end ratchet.

Secure the Plywood

When you have a piece of plywood cut to the appropriate dimensions and with the holes for rails and stiles predrilled then it's time to secure the panel to the door frame. This is a simple task that doesn't require a lot of advanced carpentry skills as long as you use the correct tools and follow the proper procedure.

Set boarding up windows and doors a table in the entrance with two sawhorses at each end, and framing lumber 2x4s. Make marks during the measurement process to guide you when cutting the plywood. Utilize a utility knife and a straight edge made of metal to score the lines. This will provide a guideline for the saw blade, and will help prevent splintering when you cut the plywood.

Wear eye protection and cut along the lines of scoring with a circular saw or table saw with a fine-tooth blade. Then sand the edges the plywood panel with 120-grit sandpaper to smooth the panels and remove any burrs that may have formed from the saw cuts. After sanding the plywood panels, apply a wood sealer and let it dry according to the instructions of the manufacturer.

Install the hinges onto the door frame. If you're using a T hinge, you need to drill holes through the exterior of the door to accommodate the strap portions of the hinges. Then, screw the hinge's outside edge to the frame using a screwdriver. Repeat the procedure for each hinge on the inside of your door. Be cautious not to overtighten them, or the panel could shift.

If you're using a single outside T-hinged door, you can make it easier to close and lock with a chain lock by fishing a piece of wire through the loops on the hinges on the outside. Fold a piece of connect wires in half and then fish it through the two holes on the exterior of the door. Then, you can twist the wires and secure the door.

Install the Plywood

Using the measurements you took, place the plywood in the door opening. Shim the header (top) of the frame and the sill (bottom). Utilize a level and make sure that there is no slop between the sill and the header. If it's not perfect then put a second shim in the area you need it and repeat the procedure until you've got the sill and the header to be plumb.

Once the plywood is in place, secure it with the stainless steel hinge bolts and wingscrews. Make use of a screwgun that has a hex head attachment to prevent removing the screws' heads.

If you live in a house boarding up service with studs that run along the length of your doorway, it is possible to drill hanger bolts into each framing member. This is a lot easier than using a drywall saw to make the hole.

After you have installed the plywood, measure the width and height of the door opening. If necessary, trim your bottom of the plywood to match the height your door frame. Cut two pieces of framing lumber 1 by 6 to form braces for the upper and lower ends. Cut along the lines that are marked on your plywood using a circular blade fitted with teeth that are finely-toothed. Wear eye protection. Take any splinters out of the cuts by using a Sanding block.

Once you've got the braces set Attach each brace to the plywood using a pair of finishing nails that measure 2 inches. When you're finished, counter sink the heads of all nails. Make sure to seal the braces and the plywood with a quality wood sealer, like this wipe on polyurethane from Minwax.

If your door is too large it is possible to add decorative molding to fill the gap between your door and jamb or you can reduce the size of your opening. In many cases it's cheaper and simpler to purchase the door. This can also alleviate any problems you might have had with the door you originally purchased if it was damaged and no suitable for the opening.